ASTM D3410 PDF

ASTM D is a testing standard designed to measure the compressive properties of polymer matrix composite materials reinforced by high-modulus fibers. ASTM D Testing Fixture. This method defines the compression properties in the plane of composite materials with polymer matrix reinforced with high. This standard is issued under the fixed designation D /D M; the number 1 This specification is under the jurisdiction of ASTM Committee D30 on.

Author: Vudot Samusho
Country: Austria
Language: English (Spanish)
Genre: Relationship
Published (Last): 24 February 2007
Pages: 252
PDF File Size: 13.43 Mb
ePub File Size: 3.47 Mb
ISBN: 170-8-85133-617-4
Downloads: 9681
Price: Free* [*Free Regsitration Required]
Uploader: Voodoolkis

The test utilizes a standard universal testing machine and a specially-designed fixture with wedge grip interfaces as described in the specification. Send us a request Wilton UK: Properties, in the test direction, that may be obtained from this test method include:. The specimen is compressed to failure.

The other two sets are shown at the lower left. Compression of Composites ASTM D Compressive properties of polymer matrix v3410 materials, by shear loading ASTM D, provides material data including compressive strength, strain, poisson’s ratio and modulus. Historical Version s – view previous versions of standard. The lower block normally rests freely on the base of the testing machine.

The test fixture is designed to provide a compressive load to the unsupported center 12 to 25 mm 0. Place the specimen in the fixture by centering it between the grip interfaces.

Sources of Additional Information: The recommended width can be 12 mm 0. The Wyoming Test Fixtures, Inc. Make sure the load reading is zero before starting the test.

TOP Related  INTRODUCTION TO HEALTH PHYSICS HERMAN CEMBER PDF

This test procedure introduces the compressive force into the specimen through shear at wedge grip interfaces. What is Third Party Certification and Accreditation for the food industry? This provides an attractive and protective storage case for the various accessories when the fixture is not in use. Formally confirming that your products and services meet all trusted external and internal standards.

Make sure that the entire grip length contacts the grip faces when the fixture is closed. Factors that influence the compressive response and should therefore be reported include the following: That is, each set of spacers provides a tabbed specimen thickness range of about 0. The suggested rates are found in the testing standard. Certification Formally confirming that your products and services meet all trusted external and internal standards.

Whether your business is local or global, we can ensure your products meet quality, health, environmental, safety, and social accountability standards for virtually any market around the world. Inspection Validating the specifications, value and safety of your raw materials, products and assets. A universal testing machine with two loading rates, with at least one moveable along the testing axis is needed to complete the test procedure.

Validating the specifications, value and safety of your raw materials, products and assets.

Compression of Composites ASTM D3410

Global Reach Intertek is the industry leader with over 43, people in 1, locations in over countries. ASTM D is commonly used for composites made from unidirectional tape, textiles, short fibers, and it can be adapted for similar products.

The fixture can be used to test nonstandard gage length specimens also, from d34110 to approximately 2″. All accessory parts for each fixture are supplied in a foam-lined, wooden storage case, fitted with brass hinges, latch, and side handles.

TOP Related  TIP132 PDF

Combining values from the two systems may result in nonconformance with the standard. One set of wedge spacers is installed in the fixture blocks.

D3401 specially-designed fixture should be attached to the upper cross head and a flat platen that is at least 20 mm 0.

A variety of thicknesses can be accommodated. The approximate thickness ranges are assuming the wedges are flush with the blocks when at the lower end of each range, and protruding a maximum of 0. Compressive properties of polymer matrix composite materials, by shear loading ASTM D, provides material data including compressive strength, strain, poisson’s ratio and modulus.

Some product forms may require deviations from the test method. Alignment rods in linear bearings are used, rather than an external alignment sleeve as in the Celanese Compression test fixture. Link to Active This link will always route to the current Active version of the standard.

Through our network of over 43, people in 1, laboratories and offices in countries, Intertek provides quality and safety solutions to a wide range of industries around the world. Need help or have a question? Evaluating how your products and services meet and exceed quality, safety, sustainability and aatm standards. This test procedure introduces the compressive force into the specimen through shear at grip interfaces. For example, the fixture can accommodate a Celanese specimen, which is also 5.

Compression of Composites ASTM D

Testing Evaluating how your products and services meet and exceed quality, safety, sustainability and performance standards. This permits easy slip-in installation and removal of the heavy upper block. Work with us to find the right equipment for your ASTM standard.

TOP Related  A SEPARATE REALITY CARLOS CASTANEDA DOWNLOAD

The composite material forms are limited to continuous-fiber or discontinuous-fiber reinforced composites for which the elastic properties are specially orthotropic with respect to the test direction.

Apply the force at a constant strain rate until failure. Sales Support Calibration Calculators.