Search among more than user manuals and view them online Find great deals for Aton DLA4 Four Room Speaker Switch With Volume Control. Shop with confidence on eBay!. Free Shipping on many items across the worlds largest range of Aton Dla4 In Home Audio Equalizers. Find the perfect Christmas gift ideas with eBay.
|Published (Last):||10 July 2015|
|PDF File Size:||2.51 Mb|
|ePub File Size:||1.61 Mb|
|Price:||Free* [*Free Regsitration Required]|
Lift up each ip-lock connector until it is locked in the up position.
Aton DLA4 Four Room Speaker Switch With Volume Control
Ground loop Ensure proper grounding using a taon prong grounded AC outlet. This is a single-source application: If within the applicable warranty period above purchaser discovers that such item was not as warranted above and promptly contacts ATON at or service atonhome.
Setting the Maximum Turn-On Volume Level to the highest volume level will essentially disable Maximum Turn-On Atoj the room will always come back on at the last volume level prior to turning the room Off.
Please keep the original sales receipt for your records and send a copy to request warranty service. Place the receiver in a convenient location; preferably as high as possible. Provisions exist for IR, Ground, and Voltage.
Like the previous example, a pair of speakers are connected to the DLA2s Room 1 Speaker Outputs, while an additional pair of speakers is connected to the Room 2 Speaker Outputs. Cut the ends of the wire to length, allowing some free play about 6 inches of slack to allow for movement when physically connecting the wire. Speakers rated between 4 Ohms and 8 Ohms can be matched with ampliers also rated from 4 to 8 Ohms. Set the volume in each room to the desired level.
Set the Zone 2 volume level to the point where it achieves the maximum listenable level prior to distortion. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
If the volume level prior to turning the lda4 off is higher than the Maximum Turn-On Volume Level, the room will come back on at the Maximum Turn-On Volume Level instead of the last volume.
You will lose any product warranty on the unit. Local Commands control only one room rla4 a time. Please report the problem to your dealer immediately. Room appears to be on and selected but unabled to be controlled using front panel buttons. Source IR Emitters unplugged or defective. Press the Room Button for the desired room. Adjust the volume as required. Remote Control Options Option 1: Verify that the impedance levels of the amp and speaker are not lower than 8 Ohms.
This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications. Room Output volume turned all the way down Increase volume.
IR Control No source control in any Room. The IR indicator will be solid red when the room is off, solid off when the room is on, or solid purple when the room is on and unselected.
At bedtime, turn off the audio throughout the entire house. Verify connections No audio present in any room Hum or buzz through system speakers Poor audio quality 26 1. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
ATON Stereo Receiver DLA4 User Guide |
This application provides independent control of each area within a sub-zone. Check IR indicator on front panel. Figure and Table provide description and location of Rear Panel connections. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: However, there is no guarantee that interference will not occur in a particular installation.
Add an optional RF remote and receiver in order to have full control anywhere in the house.
ATON DLA4 Stereo Receiver User Manual
Check Room IR receiver and verify wiring. See above Perform steps above 2. Good exercise, too – especially when your system is located downstairs or on the other side of the house. Without releasing the Room button, press and hold the Vol – Button. Follow these guidelines to ensure your device is preserved and protected.
Reconnect or test with known good IR Emitters. Warranty service requests made without proof of date of purchase will be denied. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus including amplifiers that produce heat.
Do not apply excessive amplification. Carefully peel the appropriate Room Identication Label from the card and place it in the Room Label Location for the chosen room.