The BA is a dual OTL monolithic power IC with two built-in, high outp ut speaker amplifier circuit s. High outpu tof 5W×2 can be produced when VCC=12 V. The BA is a dual-OTL monolithic power IC with two high-output, low- frequency power amplifiers. With a 12V power supply, it has a rated output of 5W 2 into. A good general purpose stereo audio amplifier electronic kit WITH HEATSINK using the ROHM BA monolithic power amplifier IC. Supplied with all.
|Published (Last):||17 April 2006|
|PDF File Size:||8.32 Mb|
|ePub File Size:||9.62 Mb|
|Price:||Free* [*Free Regsitration Required]|
The operating voltage range is from 5 to bs5406 DC. Sherwin 7 Oct Reply. Capacitor C3 is a power supply filter capacitor. Previous post Next post. And then the amplifier IC1 is not a return phase. Hi Rahul use a 22k stereo control ganged control.
5×2 watt BA stereo amplifier . Operates from 9V DC. Low distortion.
Leave a Reply Cancel reply. Many electronics circuits and projects for learning in simple ways. It can deliver 5W per channel into a 4 ohm loudspeaker at 9V supply. Add to block DC and low frequency stability.
HTTP This page has been moved
Hi Soumen you can use the following circuit a very simple one with baa5406 control operating both the channels. We think you must love this circuit. And if then how much capacity minimum audio it amplifies for?
Ba406 applications of BA are portable audio players, stereo component systems, television etc. Is going to be back often to check up on new posts. If you want to use a small stereo audio amplifier. The pin 3 and pin 10 is pin Boot Strap will help to gain a ba54066. Quote and Order boards in minutes on https: Naisarg 26 Mar Reply. This makes the IC suitable for low power car audio applications. You may also like: Your email address will not be published.
Is this circuit is useful for low output of equalizer? I just could not depart your web site prior to suggesting that I really enjoyed the standard info a person provide b5406 your visitors?
BA stereo amplifier circuit admin November 3, 11 Comments.
This circuit is small and easy to build. The C5 and C6 are connected to pins 6 and Pin 7.
The C7 and C8 are connected to pins 3 and pin 10 of IC, respectively. Then went out to the speakers. C11 and C12 are input DC decoupling capacitors for the left and right channels.
Then we enter b5a406 left and the right to access the input pin,to pin 5 and pin 8 of IC1-BA Hi, what kind of a heatsink does BA need? C9 and C10 are noise filtering capacitors.
I make it well. Ba546 site uses Akismet to reduce spam. They so suitable for expanding the use of music in a private room. When raising the power supply 12 volts to this circuit. Or may be used in any trial. Amplifiers based on BA does not require an output coupling transformer and can be operated from a single bx5406. CapacitorsC4 and C8 couple the outputs of the amplifier to the speakers.
Purpose of the Bba5406 network is to reduce oscillations and improve high frequency stability of the amplifier. I tried to search for SIP package heatsinks, but nothing good came up.
Tag: BA5406 Based 5W Stereo Audio Amplifier Circuit
What is the function of capacitor and resistor at pin 4 and 7. Learn how your comment data is processed. The audio signal pass to through the C1 and C2, are coupling signal,to prevent DC to interfere in the circuit. The exit output Pin 2 and Pin 11, and the output signal out of each channel, left and right through C9 and Ba55406 Can anyone tell how to use single pot volume control for both channels?? C1 and C5 are bootstrap capacitors for the left and right channels.
Leave a Reply Cancel reply Your email address will not be published. The BA has ba5460 channel separation, good channel isolation, small pop-up noise, low noise, low thermal resistance and is available in a 12 pin SIP package. Potentiometers R5 and R6 ba5046 as the volume control for the left and right channels.